VinFast VF 6 Grey PPF Installation with TOUCH T65MT
Project

VinFast VF 6 Grey PPF Installation with TOUCH T65MT

A VinFast VF 6 grey PPF installation uses clear paint protection film (PPF) applied over the grey paint on the front and rear of the car. This case used TOUCH T65MT film, installed at the ARI workshop on the front end and the rear sides. The film covered the bonnet, front bumper, headlights, wheel arches and rear bumper.

VinFast VF 6 Grey PPF Installation with TOUCH T65MT⛶ 1/10
Vehicle
VinFast · VF 6

On the grey paint of the VinFast VF 6, clear film still shows the flatness and detail of the body panels. A VinFast VF 6 grey PPF installation helps shield the original paint from minor impacts during daily driving, which matters because grey finishes can show scratches easily.

How the VinFast VF 6 Grey Exterior PPF Was Applied

Front corner view of a grey car, transparent PPF film being stretched and applied to the bonnet and front bumper by a person in black clothing, with the hands

Exterior PPF Work Carried Out at ARI Workshop

This job covered exterior car PPF for a grey VinFast VF 6 at the ARI workshop. The work focused on surfaces that take the most exposure to road dust and flying stones while driving.

In the installation photos, one technician stretches the clear film over the bonnet and front bumper. Beside the car, another technician continues on the headlight area, showing that the work was done panel by panel.

TOUCH T65MT Film Used and Its Specifications

Front corner view of a grey car, a technician stretching and pulling a sheet of transparent PPF film over the front bumper and headlights, with a background of

TOUCH T65MT Technical Specifications

This installation used TOUCH T65MT film, which carries a 3-year warranty. It is a paint protection film made from TPU, with these main specifications:

  • Thickness: 7.5 Mil
  • Tensile strength: above 22 MPa
  • Maximum heat resistance: 110°C
  • Surface gloss: above 90 GU
  • Coating: Nano Ceramic

These figures are the published data for the TOUCH T65MT film line. Other film codes may have different specifications, so check each one separately when choosing a film.

Panels Covered and How the Technicians Worked

Rear side view of a grey car, two technician's hands stretching and placing a sheet of transparent PPF film over the rear wheel arch and rear bumper, with the side

Bonnet, Front Bumper and Headlights

The front end was the area with the most film in this job. The film was stretched and laid over the bonnet and front bumper, while one technician held the edge of the film on the left side of the front to keep it straight.

The headlights were also within the coverage area. The technician stretched the film across the light assembly so it followed the curves of the car.

Wheel Arches and Rear Bumper

On the rear sides, two technicians stretched and positioned the film over the wheel arches and rear bumper together. A third person stood beside the car to help hold the film on the right side throughout the process.

How Should You Care for a Car After PPF Installation?

After installation, the film needs time to settle before it is exposed to strong car wash products. Wash the car with clean water and a soft cloth, and avoid abrasive cleaners on the film surface.

Parking in shade and keeping sharp objects away from the film also help it stay in good condition during normal use.

You can also look at another job in the same category: a Lynk&Co 900 black PPF installation completed by the ARI workshop.

Products Used

Frequently asked questions

How long is the TOUCH T65MT warranty?

The TOUCH T65MT film carries a 3-year warranty. This is the official figure for this film line, so it applies to the film used in this installation.

Does PPF change the colour of a grey car?

TOUCH T65MT is a clear film, so it does not add a tint to the paint surface. Its Nano Ceramic coating and gloss above 90 GU help the film keep the natural look of the grey paint underneath.

Which parts of the car were covered in this installation?

In this job, the film was applied to the bonnet, front bumper, headlights, wheel arches and rear bumper. The installation photos do not show other parts of the car being covered, so no other areas are listed.

How should you care for the car after PPF installation?

Wash the car with clean water and a soft cloth, and avoid abrasive cleaners and sharp objects. Parking in shade also helps reduce stress on the film.

Luxury car protected by ARI PPF
Join Our Network

Become an ARI Dealer

Get wholesale pricing, genuine cutting software and factory warranty support. Join the ARI installer network.